We have a 9400 showing a "framing error" on the c-arm. Monitors seem to be aok. Does anyone have any expertise/thoughts on what is causing this? We're located in Omaha, NE if there is anyone nearby available to come out & look at this unit to diagnose. Many thanks, Kris K prosystems@cox.net
The cart seems to be fine. I believe all of the connectors are making a solid connection... The C-arm display says "framing error". We can't get the unit to take an image until we get this error resolved. Thanks, Kris K
Hi Chris, Yes. We still need to troubleshoot this "framing error" issue. If you have some insight, is is possible we could hire you for some phone or face time to help diagnose? Many thanks, Kris K
I can not find that error in my 9400 training manual
list of error codes. If it was me I would replace the tech. processor PCB and disk as a matched pair. The disk and board have to match because the serial # is written to boot PROM on first boot up. All errors on the c-arm come from that board. Also check to see if the c-arm serial# matches the monitor cart serial#. Sometimes people try to mix and match these and that causes problems. Good luck!
kris i have same error.
fix,
test in techinique processor
reset techique processor 10 seg if not
remove the memory and put all pin present ground if no
change the memory and replace software.
change techinique processor and software
Altima will inspire the trust, loyalty and commitment of our customers through positive relationships and collaboration, top quality equipment services, and a clearly superior value proposition. Call Today (469) 644-7063
Kristopher Kaestner
OEC 9400 "Framing Error" question
June 16, 2010 05:52
We have a 9400 showing a "framing error" on the c-arm. Monitors seem to be aok. Does anyone have any expertise/thoughts on what is causing this? We're located in Omaha, NE if there is anyone nearby available to come out & look at this unit to diagnose. Many thanks, Kris K prosystems@cox.net
to rate and post a comment
Carlos Duran
Re: OEC 9400 "Framing Error" question
June 17, 2010 01:23
hello:
is the cart starting ok?
what happens at video out connector rear cart?
to rate and post a comment
Kristopher Kaestner
Re: OEC 9400 "Framing Error" question
June 17, 2010 02:04
The cart seems to be fine. I believe all of the connectors are making a solid connection... The C-arm display says "framing error". We can't get the unit to take an image until we get this error resolved. Thanks, Kris K
to rate and post a comment
Chris Salberg
Re: OEC 9400 "Framing Error" question
June 20, 2010 10:35
Let me know if you are still having problems with this unit. I will assist you if you are.
to rate and post a comment
Kristopher Kaestner
Re: OEC 9400 "Framing Error" question
June 20, 2010 09:18
Hi Chris, Yes. We still need to troubleshoot this "framing error" issue. If you have some insight, is is possible we could hire you for some phone or face time to help diagnose? Many thanks, Kris K
to rate and post a comment
Deon Armes
Re: OEC 9400 "Framing Error" question
July 01, 2010 04:36
Kristopher,
I can not find that error in my 9400 training manual
list of error codes. If it was me I would replace the tech. processor PCB and disk as a matched pair. The disk and board have to match because the serial # is written to boot PROM on first boot up. All errors on the c-arm come from that board. Also check to see if the c-arm serial# matches the monitor cart serial#. Sometimes people try to mix and match these and that causes problems. Good luck!
Deon Armes
to rate and post a comment
cevik sadi
Re: OEC 9400 "Framing Error" question
July 06, 2010 10:46
http://www.gmecorp-usa.com/IM/XR/CA/OEC/9400/MU/TP/oec9400_main_unit_tp_01.html
to rate and post a comment
alejandro mendoza
Re: OEC 9400 "Framing Error" question
July 12, 2010 03:12
kris
test with the backup drive flopy o
press reset 10 sec in technique processor.
regards
to rate and post a comment
alejandro mendoza
Re: OEC 9400 "Framing Error" question
July 13, 2010 10:10
kris i have same error.
fix,
test in techinique processor
reset techique processor 10 seg if not
remove the memory and put all pin present ground if no
change the memory and replace software.
change techinique processor and software
luck
to rate and post a comment