HELLO!!!!
I AM HAVING A PROBLEM WITH THE STARTUP SEQUENCE ON A C-ARM OEC9000, WHEN I TURN ON THE MACHINE THE MESSAGE ON C-ARM DISPLAY STAY IN "PLASE WAIT B8" AND NO GO FURTHER, IF ANYONE HAVE A COMMENT WILL BE APPRECIATE.
B8 = Initializing stack pointer. B8 boot code means you were stuck at booting Technique Processor board. Maybe you had a faulty Technique Processor board or a corrupted floppy disk. Double check the Technique Processor's LED read out.
Enter control panel status mode for further troubleshooting.
www.freedownloadtools.com has "PC bug doctor" free trial.
Yes, in the Technique Pocessor Bd. i have an 8 in the display, and i also tried with two differents floppy disk with the same result; is possible that may i have a problem with the floppy drive?
Thank you so much for your comment.!!!!!!!!
You have also error 8 in the LED display at the Technique Processor board it means you have a faulty TP board. Are the ICs in the sockets? Have you tried pushing the ICs into the sockets trick with power off? Inspect the board components and copper lands. Check the on board battery. You do not have a floppy drive problem because it reads the floppy disks. You do not have floppy disks problem because you tried two different disks already.
BMI-PMI services nearly every make, model, and modality through our nationwide team of nearly 200 local service engineers. Flexible contracts, 24/7 remote monitoring, and ISO 13485 certification. www.brownsmedicalimaging.com / 800-701-9729
Eduardo Vega
STARTUP PROBLEM ON OEC9000 C-ARM
June 26, 2006 08:00
HELLO!!!! I AM HAVING A PROBLEM WITH THE STARTUP SEQUENCE ON A C-ARM OEC9000, WHEN I TURN ON THE MACHINE THE MESSAGE ON C-ARM DISPLAY STAY IN "PLASE WAIT B8" AND NO GO FURTHER, IF ANYONE HAVE A COMMENT WILL BE APPRECIATE.
to rate and post a comment
Edward Yan
Re: STARTUP PROBLEM ON OEC9000 C-ARM
July 03, 2006 01:45
B8 = Initializing stack pointer. B8 boot code means you were stuck at booting Technique Processor board. Maybe you had a faulty Technique Processor board or a corrupted floppy disk. Double check the Technique Processor's LED read out.
Enter control panel status mode for further troubleshooting.
www.freedownloadtools.com has "PC bug doctor" free trial.
Edward Yan, B.S.E.E.
to rate and post a comment
Eduardo Vega
Re: STARTUP PROBLEM ON OEC9000 C-ARM
July 03, 2006 04:56
Yes, in the Technique Pocessor Bd. i have an 8 in the display, and i also tried with two differents floppy disk with the same result; is possible that may i have a problem with the floppy drive?
Thank you so much for your comment.!!!!!!!!
to rate and post a comment
Edward Yan
Re: STARTUP PROBLEM ON OEC9000 C-ARM
July 05, 2006 08:30
You have also error 8 in the LED display at the Technique Processor board it means you have a faulty TP board. Are the ICs in the sockets? Have you tried pushing the ICs into the sockets trick with power off? Inspect the board components and copper lands. Check the on board battery. You do not have a floppy drive problem because it reads the floppy disks. You do not have floppy disks problem because you tried two different disks already.
to rate and post a comment
Eduardo Vega
Re: STARTUP PROBLEM ON OEC9000 C-ARM
July 05, 2006 08:30
Thank you for the advise i will do that with the TP board and i hope that it works!!!!
Best Regards!!!!!!!
to rate and post a comment