I am in installation of one MRT50 A system which has the following symptom in booting up.
PLS let me know the details and also magnet power suply is needed.
In power on self test during initializing the diagnostic display shows 2E2C in display 2 and all of the other displays are 0.
on the monitor of main console display unit error is appeared at the right lower corner with the Nr . 17 A 0 C 5C 8 0 B is blinking continuously.
By pressing the menu key on the main console keyboard the system asks for entering the date / time/ hospital name and so on.
after pressing the end key after AFRU initialization, it looks for opt- disk INZ processing after about 3 minute it tries for Initializing 2nd console but without any success massages 2nd inz. during 2nd console initializing main menu time abort. *14-BACAF000.
During the initializing the menu OF MRI consisting of Pt.reg.,scan cond., and ..displays appeared on screen and doesn't accept any command . by pressing menu again it goes to the menu of time /date/ hospital name and that comes before AFRU initializing .
This process continues by pressing end key again and again when I take out the 2 frame memory boards in slots Nr.8 and 9 from display chassis same story is happening as well as 3 boards in slot Nr. 1, 2 and 3 that they are ARG/FM, ALU, UP CNT, respectively.
The system consists only 1 hard disk that is smaller than the other hard disks from other MRT 50s Which I have ever seen.
there is no MOD in the system at all.
in the CPU chassis the slots are occupied by the following boards
CPU chasis
Slot N r . Board
00 Cpu
01
02 IF/MOD Record
03 I dont know what board it is.
04 TIF
05 SHF
06 *
07 SHF
O8 TSI F
09 *
10 *
11 AFRU inter face
"*" means that slot is empty.
The second console is blank all of the time.
PLS let me know what is the problem and how can I boot the software.
If U know experts in this regards I would really appereciate if U connect me to them.
Sell your scrap MRI magnets! Top prices, free shipping, and fast pickups. Don't let dust-collecting, idle assets go to waste. Contact: ryan.swiderski@cyclicmaterials.earth or call 437-826-1621
Bagher Mahdavi
MRT50A/2 help needed
September 14, 2003 04:14
Hello Groups.
I am in installation of one MRT50 A system which has the following symptom in booting up.
PLS let me know the details and also magnet power suply is needed.
In power on self test during initializing the diagnostic display shows 2E2C in display 2 and all of the other displays are 0.
on the monitor of main console display unit error is appeared at the right lower corner with the Nr . 17 A 0 C 5C 8 0 B is blinking continuously.
By pressing the menu key on the main console keyboard the system asks for entering the date / time/ hospital name and so on.
after pressing the end key after AFRU initialization, it looks for opt- disk INZ processing after about 3 minute it tries for Initializing 2nd console but without any success massages 2nd inz. during 2nd console initializing main menu time abort. *14-BACAF000.
During the initializing the menu OF MRI consisting of Pt.reg.,scan cond., and ..displays appeared on screen and doesn't accept any command . by pressing menu again it goes to the menu of time /date/ hospital name and that comes before AFRU initializing .
This process continues by pressing end key again and again when I take out the 2 frame memory boards in slots Nr.8 and 9 from display chassis same story is happening as well as 3 boards in slot Nr. 1, 2 and 3 that they are ARG/FM, ALU, UP CNT, respectively.
The system consists only 1 hard disk that is smaller than the other hard disks from other MRT 50s Which I have ever seen.
there is no MOD in the system at all.
in the CPU chassis the slots are occupied by the following boards
CPU chasis
Slot N r . Board
00 Cpu
01
02 IF/MOD Record
03 I dont know what board it is.
04 TIF
05 SHF
06 *
07 SHF
O8 TSI F
09 *
10 *
11 AFRU inter face
"*" means that slot is empty.
The second console is blank all of the time.
PLS let me know what is the problem and how can I boot the software.
If U know experts in this regards I would really appereciate if U connect me to them.
Best
Bagher mahdavi
to rate and post a comment
shahzad Ahmad
Re: MRT50A/2 help needed
September 16, 2004 02:54
if you still have problems to install the MRI, please contact us we can help you to install/service as we are a group of engineers from Pakistan.
to rate and post a comment
Bagher Mahdavi
Re: MRT50A/2 help needed
September 19, 2004 08:56
Hi there
I have installed it
but like to have closer connection with U about furthere details.
@nd console doesnt work.
Best
Bagher
to rate and post a comment