Hi everybody. We have Kodak DR-9000 it gives E43 error. Which means up/down limit problem. Does anybody has any opinion what is the problem and how to fix it.
Have you checked the down limit switch located on top of and to the front of the over head tube support and the up limit switch at the top of the tube column?
Hello
I found this part of the documentation, can you help:
In the following steps, verify that the UP and Down switches operate correctly at both panel locations.
14. Verify vertical travel by pressing DOWN and verifying smooth and quiet travel. Verify the vertical motor stops when the positioner column reaches its lower travel limit and does not continue to drive against the stop. The top digital display shall alternately display "E41" along with the SID.
15. Verify vertical travel by pressing UP and checking for smooth and quiet travel. Also verify the vertical motor stops when the positioner column reaches its upper travel limit and does not continue to drive against the stop. The top digital display shall alternately display "E43" along with the SID.
16. Verify the automatic vertical collision sensing by placing an object, such as a chair, beneath the vertical column and pressing DOWN, lowering the vertical column against the object. Verify that the motor stops without excessive force when the collision sensor comes into contact with the object. The top digital display
shall alternately display "L83" along with the SID. Verify that the column automatically stops moving when DOWN and UP are selected simultaneously.
I greet
Roman
For a Versarad System: To override software limits - On the Smart Amp PCB move SW1-2 and 3 to the open position (to the right) Try to drive the column down. Re-Enable software limits to get back to normal mode. If you hit a mechanical limit while the software limits are overridden you will have to clear the error as follows: Lift the activated switch in the carriage and while holding the carriage switch hit reset on the Traumex logic PCB and run the arm up or down off of the limit. Then release the carriage switch.
North America's trusted source for ultrasound probe repair and certified refurbished OEM probes. Free evaluations, 1-year warranty, fast turnaround for GE, Philips, Sonosite, Canon, Toshiba, and more. Call (224) 265-7640 / Sales@Lenard.Healthcare
Akmaljon Turaev
KODAK DR-9000 E43 error
November 21, 2012 12:31
Hi everybody. We have Kodak DR-9000 it gives E43 error. Which means up/down limit problem. Does anybody has any opinion what is the problem and how to fix it.
to rate and post a comment
tim cowell
re: KODAK DR-9000 E43 error
November 23, 2012 12:12
Have you checked the down limit switch located on top of and to the front of the over head tube support and the up limit switch at the top of the tube column?
to rate and post a comment
Akmaljon Turaev
re: re: KODAK DR-9000 E43 error
November 26, 2012 10:22
sure. When you click the up or down buttons but no change.
to rate and post a comment
John Edwards
re: re: KODAK DR-9000 E43 error
November 30, 2012 06:12
Do you have service CD for Digital Pan 8000 by Kodak Mr Cowell? If so please e-mail to JEdward3@adventisthealthcare.com
to rate and post a comment
romanz
re: KODAK DR-9000 E43 error
November 24, 2012 11:43
Hello
I found this part of the documentation, can you help:
In the following steps, verify that the UP and Down switches operate correctly at both panel locations.
14. Verify vertical travel by pressing DOWN and verifying smooth and quiet travel. Verify the vertical motor stops when the positioner column reaches its lower travel limit and does not continue to drive against the stop. The top digital display shall alternately display "E41" along with the SID.
15. Verify vertical travel by pressing UP and checking for smooth and quiet travel. Also verify the vertical motor stops when the positioner column reaches its upper travel limit and does not continue to drive against the stop. The top digital display shall alternately display "E43" along with the SID.
16. Verify the automatic vertical collision sensing by placing an object, such as a chair, beneath the vertical column and pressing DOWN, lowering the vertical column against the object. Verify that the motor stops without excessive force when the collision sensor comes into contact with the object. The top digital display
shall alternately display "L83" along with the SID. Verify that the column automatically stops moving when DOWN and UP are selected simultaneously.
I greet
Roman
to rate and post a comment
tim cowell
re: KODAK DR-9000 E43 error
November 28, 2012 10:25
For a Versarad System: To override software limits - On the Smart Amp PCB move SW1-2 and 3 to the open position (to the right) Try to drive the column down. Re-Enable software limits to get back to normal mode. If you hit a mechanical limit while the software limits are overridden you will have to clear the error as follows: Lift the activated switch in the carriage and while holding the carriage switch hit reset on the Traumex logic PCB and run the arm up or down off of the limit. Then release the carriage switch.
to rate and post a comment