We provide sales, service, rental, and repair for ultrasound systems, probes, and C-arms. We have the largest inventory in the world. Contact us about our special offers on certified refurbished equipment! Call: 317-759-9210 Email: sales@probomedical.com.
(53)
Laura Carolina Gonzales Calderon
VOLUSON 730 MOTCRTL ERROR
May 24, 2013 03:31
Regards
I have a problem whit voluson 730, probe connected and begin 4d explorer appear MotCtrl: No Referenzposition signali!
Action: comfirm the message by pressing the ok button,
desconnect and connect the active probe and use it again,
if again the message appea mostly the probe itself has an defect,
so you should contac the tecnical support., you can help me, thanks in advance
to rate and post a comment
(61)
(13)
Ricardo A. Sanchez
re: VOLUSON 730 MOTCRTL ERROR
May 24, 2013 05:38
have you try to test that probe in another machine? usually the probe is bad, does not recognize the Null position or is Jam
to rate and post a comment
(5)
(34)
Jaime Munoz
re: VOLUSON 730 MOTCRTL ERROR
May 24, 2013 08:47
Your problem is your probe. Most likely somebody hit the probe and the cristal gets out of sync. We can repair it for you. Send me an email info@jacomed.com
to rate and post a comment
(1)
Jose Moreno
re: re: VOLUSON 730 MOTCRTL ERROR
May 28, 2013 10:33
I have the same problem, but my Probe is GE RAB4-8-D
will send you an email hope it can be repair.
to rate and post a comment
Mạnh Hùng
re: re: VOLUSON 730 MOTCRTL ERROR
September 20, 2017 09:12
Hello.
I'm having problems, the 2D function is working perfectly, but the 4D function has the same error. I live in Vietnam. You can support me repair the probe ??
Thank you !
to rate and post a comment
(3)
(1)
morteza yousefi
re: VOLUSON 730 MOTCRTL ERROR
October 11, 2013 06:05
this probe is defective for 4D.the motor roteit cristal is jamed.mey some enginier can open it and ripeir it
to rate and post a comment
Franz Alexis Ramirez franco
re: re: VOLUSON 730 MOTCRTL ERROR
June 15, 2021 10:10
I have a problem with a voluson 730 ultrasound, it recognizes the probes but in the spectral focus the screen appears blank, there is no response or stimulus, nor is acoustic interference perceived, only this white screen is displayed
to rate and post a comment
JohnDang
re: re: re: VOLUSON 730 MOTCRTL ERROR
July 07, 2021 11:46
CRS issue, Sir
to rate and post a comment
(14)
(6)
Fabio Barcherini
re: VOLUSON 730 MOTCRTL ERROR
June 16, 2015 09:38
Hello , I read now your old post, how have you solved the problem ?I have the same .
to rate and post a comment
ruben rodriguez
re: VOLUSON 730 MOTCRTL ERROR
October 05, 2017 09:04
MotCtrl: No Referenzposition signali!
Action: comfirm the message by pressing the ok button,
desconnect and connect the active probe and use it again,
to rate and post a comment
JohnDang
re: VOLUSON 730 MOTCRTL ERROR
July 07, 2021 11:46
If the error always displayed when you choose 4D probe
we have 2 case of this:
1) problem because probe => you have to check another 4D probe.
-the sensor or magnet got error => how to check : when choosing probe, you can hear or feel moving of motor.
-motor error => you can not hear or feel motor runs.
- cables from the dock to the probe is broken.
2) CRS or CPP and the last CPV => if you have another probe 4D RAB2-5, RAB4-8 or RIC5-9 on this machine, If using these probe still got this error, It's board error.
I can not help you more because it is deep inside technical.
to rate and post a comment