I need help on following errors :
1016 -HIGH_SPEED_STARTER_FAULT_LATCH and
1017 -HIGH_SPEED_STARTER_DRIVER I need help on proper troubleshooting to find trouble.
hello friend
im experiencing the problem in PQS picker ctscanner
no error is shown but when i try the switch on 3rd time for ready
No READY light on at console
and on XSC RED light on of rotating frame in fault
and in AC CHASSIS on the Board logic control interface two leds are on
1.OVLFT
2.FAULT
PLEASE GUIDE ME HOW I SOLVE IT I CHECKED ALL FUSES
SOme questions:
Do the equipment perform warm up?
If you have warm up nor HSS or TUBE are the problem.
Each error that appear must show another number named TRACER. Do you can supply these TRACER numbers?
You need to check the sound the anode produce at spinning. Noisy sound mean bad tube. Also no sound may mean bad tube but is not the only cause.
hello friend
im experiencing the problem in PQS picker ctscanner
no error is shown but when i try the switch on 3rd time for ready
No READY light on at console
and on XSC RED light on of rotating frame in fault
and in AC CHASSIS on the Board logic control interface two leds are on
1.OVLFT
2.FAULT
PLEASE GUIDE ME HOW I SOLVE IT I CHECKED ALL FUSES
Your problem is on the HHS, the X-ray tube or both parts. If you can make intermittent exposures then you can rule that the HHS it may be OK and your problem is the tube, check the noise of the rotor whenever you make an exposure. If you prep and the HHS try to rotate the rotor then the tube is your problem. Look at the leds on the HHS.
dear sir,
it is good to check the fuses on the HSS, for me i will open the cover of the HSS and check the SCRs and the other components
i remember i got HSS drive error i will check it for you.
pls send me a photo for the long discription of the error.
bkalash71@yahoo.com
hello friend
im experiencing the problem in PQS picker ctscanner
no error is shown but when i try the switch on 3rd time for ready
No READY light on at console
and on XSC RED light on of rotating frame in fault
and in AC CHASSIS on the Board logic control interface two leds are on
1.OVLFT
2.FAULT
PLEASE GUIDE ME HOW I SOLVE IT I CHECKED ALL FUSES
Did you check Leds on the HSS?When you perform warm up check it.If there is a fault please check to fuses on the HSS,if there are blown fuses replace to the HSS
hello friend
im experiencing the problem in PQS picker ctscanner
no error is shown but when i try the switch on 3rd time for ready
No READY light on at console
and on XSC RED light on of rotating frame in fault
and in AC CHASSIS on the Board logic control interface two leds are on
1.OVLFT
2.FAULT
PLEASE GUIDE ME HOW I SOLVE IT I CHECKED ALL FUSES
CHECK AC IN VOLTAGES ARE BETWEEN 460 AND 512 IN EACH PHASE
CHECK FUSES NEAR CONTACTOR IN THE BACK OF GANTRY AND IN THE SIDE OF AC INPUT BLOCK. YOU WILL NEED TO TURN OFF ENERGY FROM THE WALL AND DISCONNECT FUSES FOR TRUE CHECK.
If voltages are ok, probably ac diagnostic board inside the ac input module is defective
rotary Fault showed for xsc is normal when ready light is off. Of course, you must check all fuses to be sure. Be sure gullwing switch on front door is working fine too.
Adepto Medical is an infusion pump rental, sales, and service company. Our focus is to deliver to our customers the best product and customer service support we can offer. Call (913) 261-9933
(6)
(5)
Alessandro Lazzari
Picker 2000
July 12, 2011 09:13
I need help on following errors :
1016 -HIGH_SPEED_STARTER_FAULT_LATCH and
1017 -HIGH_SPEED_STARTER_DRIVER I need help on proper troubleshooting to find trouble.
to rate and post a comment
(38)
(5)
Juan de la Cruz Martinez
Re: Picker 2000
July 12, 2011 11:05
Check XCS, DIB, HVG, Cables fuses or Emergency Stop.
to rate and post a comment
Mazher saeed
re: Re: Picker 2000
March 02, 2013 09:11
hello friend
im experiencing the problem in PQS picker ctscanner
no error is shown but when i try the switch on 3rd time for ready
No READY light on at console
and on XSC RED light on of rotating frame in fault
and in AC CHASSIS on the Board logic control interface two leds are on
1.OVLFT
2.FAULT
PLEASE GUIDE ME HOW I SOLVE IT I CHECKED ALL FUSES
to rate and post a comment
(5)
Alvaro Moreira
Re: Picker 2000
July 12, 2011 02:04
You have either a bad HSS module or a broken tube.
Alvaro Moreira
to rate and post a comment
Mazher saeed
re: Re: Picker 2000
March 05, 2013 08:38
thanks friends
to rate and post a comment
Rajoo
re: re: Re: Picker 2000
March 13, 2014 08:04
Plz your tube has less oil . u can cotect me for further guidence on my mail. comd81@gmail.com
to rate and post a comment
(25)
(6)
Jose Morillo
Re: Picker 2000
July 12, 2011 07:28
SOme questions:
Do the equipment perform warm up?
If you have warm up nor HSS or TUBE are the problem.
Each error that appear must show another number named TRACER. Do you can supply these TRACER numbers?
You need to check the sound the anode produce at spinning. Noisy sound mean bad tube. Also no sound may mean bad tube but is not the only cause.
Check fuses inside the HSS module.
to rate and post a comment
Mazher saeed
re: Re: Picker 2000
March 02, 2013 09:11
hello friend
im experiencing the problem in PQS picker ctscanner
no error is shown but when i try the switch on 3rd time for ready
No READY light on at console
and on XSC RED light on of rotating frame in fault
and in AC CHASSIS on the Board logic control interface two leds are on
1.OVLFT
2.FAULT
PLEASE GUIDE ME HOW I SOLVE IT I CHECKED ALL FUSES
to rate and post a comment
Mazher saeed
re: Re: Picker 2000
March 05, 2013 08:38
friend no error is shown and it bcome not ready my xsc is ok and light is ON of hss in fault
but hss show fault led on
to rate and post a comment
(2)
Ernesto Guerra
Re: Picker 2000
July 12, 2011 10:36
Your problem is on the HHS, the X-ray tube or both parts. If you can make intermittent exposures then you can rule that the HHS it may be OK and your problem is the tube, check the noise of the rotor whenever you make an exposure. If you prep and the HHS try to rotate the rotor then the tube is your problem. Look at the leds on the HHS.
to rate and post a comment
(13)
(2)
Borhan Kalash
Re: Picker 2000
July 14, 2011 09:12
dear sir,
it is good to check the fuses on the HSS, for me i will open the cover of the HSS and check the SCRs and the other components
i remember i got HSS drive error i will check it for you.
pls send me a photo for the long discription of the error.
bkalash71@yahoo.com
to rate and post a comment
Mazher saeed
re: Re: Picker 2000
March 02, 2013 09:11
hello friend
im experiencing the problem in PQS picker ctscanner
no error is shown but when i try the switch on 3rd time for ready
No READY light on at console
and on XSC RED light on of rotating frame in fault
and in AC CHASSIS on the Board logic control interface two leds are on
1.OVLFT
2.FAULT
PLEASE GUIDE ME HOW I SOLVE IT I CHECKED ALL FUSES
to rate and post a comment
Rajoo
re: re: Re: Picker 2000
November 08, 2014 09:39
Less oil in tube plz check.
to rate and post a comment
Rajoo
re: re: Re: Picker 2000
November 17, 2014 11:04
waqar
check your XSC board might be faulty.
to rate and post a comment
(1)
Sanchez Navarro
Re: Picker 2000
July 13, 2011 10:03
Did you check Leds on the HSS?When you perform warm up check it.If there is a fault please check to fuses on the HSS,if there are blown fuses replace to the HSS
to rate and post a comment
Mazher saeed
re: Picker 2000
March 02, 2013 09:11
hello friend
im experiencing the problem in PQS picker ctscanner
no error is shown but when i try the switch on 3rd time for ready
No READY light on at console
and on XSC RED light on of rotating frame in fault
and in AC CHASSIS on the Board logic control interface two leds are on
1.OVLFT
2.FAULT
PLEASE GUIDE ME HOW I SOLVE IT I CHECKED ALL FUSES
to rate and post a comment
(25)
(6)
Jose Morillo
re: re: Picker 2000
March 03, 2013 09:42
CHECK AC IN VOLTAGES ARE BETWEEN 460 AND 512 IN EACH PHASE
CHECK FUSES NEAR CONTACTOR IN THE BACK OF GANTRY AND IN THE SIDE OF AC INPUT BLOCK. YOU WILL NEED TO TURN OFF ENERGY FROM THE WALL AND DISCONNECT FUSES FOR TRUE CHECK.
If voltages are ok, probably ac diagnostic board inside the ac input module is defective
rotary Fault showed for xsc is normal when ready light is off. Of course, you must check all fuses to be sure. Be sure gullwing switch on front door is working fine too.
to rate and post a comment
Mazher saeed
re: re: re: Picker 2000
March 05, 2013 08:39
thanks
to rate and post a comment
Rajoo
re: re: Picker 2000
November 17, 2014 11:04
Waqar . You must replace small switch attached with BLACK THREE PHASE SWITCH placed in side the HSS.
to rate and post a comment
Mazher saeed
re: Picker 2000
March 05, 2013 08:38
hss and xsc to be checked
to rate and post a comment