Over 90 Total Lots Up For Auction at One Location - WA 04/08

DMR+ Help

Tags: Mammo, GE DMR+

(62)
(11)

zekeng brice

DMR+ Help

November 13, 2013 08:34

hi to all
please I have a problem with dmr+ I had E3 Rotor failure 017/003 it was the rotor control board after change the fuse F4 ;F6 and replace the six irf 450.and some zener diode fuses are not more blew and the same error remain and the rotor can't start please what can be the matter .?

Log inor Register

to rate and post a comment

(62)
(11)

zekeng brice

re: DMR+ Help

November 13, 2013 04:05

the error change to E03 rotor failure 017/002 not 017/003 as I said before

Log inor Register

to rate and post a comment

(128)
(10)
(15)

Johnny Barreto

re: re: DMR+ Help

November 14, 2013 08:57

I'll send you the asm of the DMR+, tell me your email address

Log inor Register

to rate and post a comment

(62)
(11)

zekeng brice

re: re: re: DMR+ Help

November 15, 2013 06:45

helo my email is azombouzekeng@gmail.com

Log inor Register

to rate and post a comment

(3)

SAJITH A V

re: re: re: DMR+ Help

May 13, 2014 10:17

sir, can u pls send me the asm of dmr=.. , sajithvkurup@gmail.com

Log inor Register

to rate and post a comment

diogenes amaro

re: re: re: DMR+ Help

April 19, 2015 10:08

Hi Johnny I am having the same problem please send me the ASM of the DMR to this email damaro@medicalsolutions.com.do Thank you very much

Log inor Register

to rate and post a comment

CHRIS NALMPANTIS

re: re: DMR+ Help

November 14, 2013 08:57

HI YOUR PROBLEM IS THAT THE ANODE DO NOT RISE THE 7000 RPM
THAT MAY HAVE PROBLEM TO THE ROTOR BOARD OR THE TUBE IT SELF.DID YOU TRY TO CHECK THE TUBE?

Log inor Register

to rate and post a comment

(62)
(11)

zekeng brice

re: re: re: DMR+ Help

November 15, 2013 06:45

I Didn't thing about the tube because I had this problem before systematically it affect the rotor board and blowing the irf and others now it is not more the case as I said before this is why I can't suspect it now

1 person liked this
Log inor Register

to rate and post a comment

(128)
(10)
(15)

Johnny Barreto

re: re: re: re: DMR+ Help

November 15, 2013 12:48

Waw, I'm having the same problem, bought and exchanged ten IRF Mosfets. By now getting the error 017/003 and not knowing where to go on this issue

Log inor Register

to rate and post a comment

(4)

Hector Guardia

re: re: re: re: re: DMR+ Help

November 22, 2013 05:49

Hi, did you find what was the problem with the error??

Log inor Register

to rate and post a comment

(10)

(1)

Jose Pinto

re: re: re: re: re: DMR+ Help

October 17, 2015 09:55

Dear Jhonny,
How did you get rid of error 017/003
if you could give me some Ideas, I keep getting this errors and changing IFR 450, diodes and coils in in the rotor board, sometimes system make some x-ray then it burn IFR and related fuses again
I appreciate your or anyone who want to share same experience

Log inor Register

to rate and post a comment

(24)
(9)

cristian oliveira

re: re: DMR+ Help

November 14, 2013 03:04

Probaly you have a problem on coil of rotor board.
Change the board.

Log inor Register

to rate and post a comment

(72)
(18)

tim cowell

re: DMR+ Help

November 14, 2013 03:28

E3 017/003 not rising during acceleration to 6000 RPM useing large filament. E3 017/002 not rising during acceleration to 9000 RPM useing small filament. If you have power to 300PL1 (Inverter Board) from 200PL2, failure probably is 300PL1 board.

Log inor Register

to rate and post a comment

(3)

SAJITH A V

re: DMR+ Help

May 13, 2014 10:17

Sir, i am facing the same issue, can u help me...

Log inor Register

to rate and post a comment

(34)
(1)

JUAN PAULO REYES CASTILLO

re: DMR+ Help

June 01, 2015 08:48

the problem is the noise from the power supply DC/DC

Log inor Register

to rate and post a comment

(10)

(1)

Jose Pinto

re: re: DMR+ Help

October 17, 2015 09:54

Dear Juan,
I am having same problem with error 017/003 very often
can you provide support to me, if so please send me your email
Thanks

Log inor Register

to rate and post a comment

(10)

(1)

Jose Pinto

re: DMR+ Help

October 17, 2015 09:54

Dear Zeikeng
How did you get rid of error 017/003
if you could give me some Ideas, I keep getting this errors and changing IFR 450, diodes and coils in in the rotor board, sometimes system make some x-ray then it burn IFR and related fuses again
I appreciate your or anyone who want to share same experience

Log inor Register

to rate and post a comment

(62)
(11)

zekeng brice

re: re: DMR+ Help

October 18, 2015 12:09

hello dear pinto don't think too much just change the tube assembly and your problem is solve

1 person liked this
Log inor Register

to rate and post a comment

(2)

neriio zarrate

re: re: re: DMR+ Help

February 10, 2017 10:17

My estimate would like to know how it gave solution to the error E03 017/003, so that it shares the information .. thanks nerio83@hotmail.com

Log inor Register

to rate and post a comment

(2)

neriio zarrate

re: DMR+ Help

February 09, 2017 04:48

My estimate would like to know how it gave solution to the error E03 017/003, so that it shares the information .. thanks nerio83@hotmail.com

Log inor Register

to rate and post a comment

stats
DOTmed text ad

Stretcher Rentals

50+ Stretchers in stock for immediate rentals. Contact us for a today for a quote.

DOTmed Certified DOTmed 100 stats
advertisement

Upcoming Auction Events

NorthWest Supply
TIMED
Apr 08, 2024 (98 lots)